product name

Troy-Bilt 12064 Horse-OPC (7&8HP) Rototiller (S/N 120640100101-Up) Horse

Model: 511888

Back To Assemblies

Save
 Part Not Listed?Part Not Listed?
product name

WHEEL SPEED LEVER, BELT DRIVE, ENGINE & WHEELS

...
...
1
PIN - spring, 1/8" dia., retains castle nut to threaded stud MTD-GW-9362
...
2
NUT-HEX 1/2-20 (CALL TECH SERV. DEPT. FOR TIGHTENING INSTRUCTIONS) MTD-9838
...
3
WASHER- shoulder, 1/2" (shoulder faces disc washers) MTD-GW-9934
...
4
WASHER- disc spring (concave surfaces face each other) MTD-GW-9932
...
5
LEVER - wheel speed shift INCL. #6 & #18. "PRESS-IN" GREASE ZERK ADDED S/N'S 120560304830 & HIGHER, 120570302206 & HIGHER, 120580305021 & HIGHER, 120590304519 & HIGHER. MTD-GW-2628
...
6
KNOB - wheel speed shift lever MTD-1902240
...
7
PIN - cotter, 3/32" x 1" MTD-GW-9317
...
8
ROD - connecting rod, wheel speed shift lever MTD-GW-1231
...
9
SWIVEL - connecting rod MTD-GW-1033
...
10
WASHER - flat, 5/16",S.A.E. MTD-736-0567
...
11
PIN - hair cotter MTD-714-04048
...
12
Hex Lock Nut, 5/16-18 MTD-912-0158
...
13
Hex Flange Screw, 3/8-16 MTD-710-04042
...
14
L-Wash. 3/8" I.D. MTD-736-0169
...
15
Washer, Plain (flat) 3/8, S.A.E. MTD-736-3050
...
16
BUSHING - spacer, 21/64" (.325") long, yoke to engine mount MTD-GW-2146
...
17
BUSHING - spacer, 19/64" (.300") long, yoke link to retaining plug MTD-GW-1113-1099
...
18
RING- retaining (tolerance ring) MTD-GW-9120
...
19
BLOCK - belt adjustment, 3-7/8" long MTD-GW-1920
...
20
ROD - belt adjustment, 7" long, with measuring gauge MTD-GW-2100
...
21
DECAL-STARTING STABIL MTD-1900766
...
22
BOLT - hex. hd., 3/8"-24 x 1-1/2", engine pulley MTD-710-0459A
...
23
DISC-reverse, rubber rimmed MTD-GW-1919
...
23
DISC ONLY-reverse, rubber rimmed MTD-756-04171
...
24
BELT -forward drive MTD-GW-9245
...
25
PULLEY- engine P.T.O. (Power Take Off) MTD-619-04124
...
26
SHIM - engine pulley, 1/16" thick MTD-736-04187
...
26
SHIM - same as above, 1/32" thick MTD-736-04192
...
27
KEY - engine pulley, 3/16" square x 2-1/2" MTD-GW-9303
...
28
Hex Screw, 5/16-18 x 1.00 MTD-710-0376
...
29
HEX NUT 5/16-18 MTD-712-3010
...
30
BAR- engine mounting MTD-GW-1034A
...
31
PLUG - thread protector, red plastic MTD-GW-9147
...
32
BOLT- hex. hd., 5/16"-24 x 1-1/8", engine mounting MTD-710-0672
...
33
LOCK WASHER 5/16 MTD-936-0119
...
34
Motor Mount MTD-719-04222-0637
...
35
7HP B&S RECOIL START MOD. #171432, TYPE #0529. MTD-NA
...
35
7HP B&S ELEC. START MOD. #171437, TYPE #0530. MTD-NA
...
?36
8HP B&S RECOIL START MOD. #195432, TYPE #0857. MTD-NA
...
?36
8HP B&S ELEC. START MOD. #195437, TYPE #0858. MTD-NA
...
37
8HP KOHLER RECOIL START. MOD. #M8T SPEC. #PS-301608. MTD-NA
...
37
8HP KOHLER ELEC. START. MOD. #M8ST SPEC. #PS-301609. MTD-NA
...
38
DECAL-HOT SURFACE MTD-55053
...
39
DECAL-STABIL STARTING MTD-1900767
...
40
WEIGHT-ENG ECONO PNT MTD-2522
...
41
Screw-Hex 5/16-18 MTD-710-0395
...
42
SPACER-.88X.385X.09 ZP MTD-GW-20553
...
43
PIN -roll (spirol, 5/16" x 1-1/2" long, wheel hub to shaft NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-GW-9322099
...
44
ASSM-STD TIRE NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-GW-9142
...
45
TIRE-LT BT GARDEN TRAC (WHITE) NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-GW-9143
...
45A
TIRE-RT BT GARDEN TRAC (WHITE) NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-GW-9144
...
45
ASSM-TIRE&WHEEL LH GRAY NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-2709-01
...
45A
ASSM-TIRE&WHEEL RH GRAY NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-2709-02
...
46
CAP - wheel hub NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-1902020
...
xx
TIRE 16.25 X 4.5-8 NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-734-0808A
...
xx
RIM-WHEEL 8" GRAY NOTE: BAR TREAD TIRES SHOULD BE MOUNTED ON THE TILLER SO THAT THE END OF THE "V" IN THE TIRE TREAD ON TOP OF THE TIRE WILL FACE FORWARD. MTD-GW-2708
...
...
...
Processing